A formulation team runs an approved fertilizer batch that uses Zinc Sulfate Monohydrate 33% as its zinc source and now plans to replace it with Zinc Sulfate Monohydrate 36%. The finished batch weight and the elemental zinc delivered by this ingredient must both stay the same. Because the two grades carry different zinc fractions, loading the same kilograms of the new grade would raise the zinc dose and change the formula.
For teams evaluating Zinc Sulfate Monohydrate 33% & 36% from Shivam Agro Industries, the grade decision therefore reaches beyond purchasing into the batch sheet itself. The example in this article follows one hypothetical batch through that switch.
Confirming the Elemental Zinc Assay for Zinc Sulfate Monohydrate 33% and 36%
The recalculation is only as accurate as the zinc fraction entered into it. Before any arithmetic, the formulation and QA teams should confirm four inputs for both the original and the replacement material:
- Product grade. Confirm that the grade received matches the grade named in the formula revision.
- Lot identification. Confirm the lot number so the assay can be traced to the material on the production floor.
- Elemental zinc assay. Confirm the elemental zinc assay for the lot, expressed as a percentage of the material.
- Reporting basis. Confirm whether that result is reported as received or on a dry basis.
A grade label such as 33% or 36% states what the product is offered as. The technical specification table that Shivam Agro Industries publishes for this product, covering parameters such as description, solubility, identification and pH, describes its stated characteristics. Neither replaces a measured lot result, which describes the specific material being weighed and is the value the calculation needs.
The reporting basis matters because the plant weighs material as it arrives. Use an as received zinc fraction for material weighed as received. If only a dry basis result is available, confirm the information needed to establish a comparable as received value, such as the moisture or loss on drying figure for the same lot, before proceeding.
Recalculating Zinc Sulfate Monohydrate Weight for the Same Zinc Target
The worked example uses the following hypothetical values. They illustrate the method only and are neither recommended rates nor actual Shivam Agro Industries lot results.
| Hypothetical input | Value |
|---|---|
| Finished fertilizer batch weight | 1,000 kg |
| Elemental zinc required from this ingredient | 10 kg |
| Assumed as received elemental zinc assay, original material | 33.0% |
| Assumed as received elemental zinc assay, replacement material | 36.0% |
The required weight of any zinc source follows one relationship:
Ingredient weight = required elemental zinc weight ÷ elemental zinc mass fraction
Expressed as mass fractions, 33.0% becomes 0.330 and 36.0% becomes 0.360.
Zinc Sulfate Monohydrate 33% (original entry): 10 ÷ 0.330 = 30.30303 kg, displayed as approximately 30.303 kg
Zinc Sulfate Monohydrate 36% (replacement entry): 10 ÷ 0.360 = 27.77778 kg, displayed as approximately 27.778 kg
Weight reduction: 30.30303 kg less 27.77778 kg leaves 2.52525 kg, displayed as approximately 2.525 kg
Keep full precision during the calculation, then round the final weights to the scale’s resolution and recheck the batch total and zinc contribution.
The size of the error avoided is worth noting. Loading 30.303 kg of the 36% material would have supplied about 10.909 kg of zinc, roughly 9% above the target.
Rebalancing the Fertilizer Formula After the Zinc Grade Change
The lighter zinc line leaves the batch about 2.525 kg short of 1,000 kg, and that mass has to be restored without disturbing the rest of the formula.
For this example, assume the approved formula includes an adjustable carrier at 200.000 kg, with all other ingredients totalling 769.697 kg. The carrier rises by approximately 2.525 kg and every other quantity stays fixed.
| Formula line | Original formula (kg) | Revised formula (kg) | Adjustment |
|---|---|---|---|
| Zinc sulfate monohydrate | 30.303 (33% grade) | 27.778 (36% grade) | Reduced by 2.525 kg |
| Adjustable carrier | 200.000 | 202.525 | Increased by 2.525 kg |
| All other ingredients | 769.697 | 769.697 | No change |
| Finished batch weight | 1,000.000 | 1,000.000 | No change |
| Calculated zinc from this ingredient | 10.000 | 10.000 | No change |
The revised zinc line checks out at 27.778 × 0.360 ≈ 10.000 kg, and both columns total 1,000.000 kg.
If the real formula has no adjustable carrier, the formulation team must confirm an approved adjustment before production. The difference should not be absorbed by another nutrient ingredient by default, because that would alter the nutrient profile the formula was approved to deliver.
Verifying the Revised Zinc Sulfate Monohydrate Fertilizer Batch
Verification supports two separate decisions: whether the batch can be made, and whether the finished batch can be released.
Before production, confirm:
- The formula revision is approved and records the new grade, the revised zinc line and the carrier adjustment.
- The material staged for the batch is the approved grade and the same lot whose assay was used.
- The target weights in the batch record match the revised formula.
- The targets still work at the scale’s actual weighing precision. On a scale reading to 0.1 kg, the revised batch uses 27.8 kg of zinc sulfate monohydrate, 202.5 kg of carrier and 769.7 kg of other ingredients, for a total of 1,000.0 kg. The zinc line then contributes 10.008 kg of elemental zinc. Here 769.7 kg is the rounded aggregate for this example, so check the sum of the actual rounded ingredient lines before production, and confirm that the zinc deviation sits within the team’s own formula tolerance.
After production, confirm actual weights against the batch record, then apply the team’s documented sampling, testing and release criteria.
The calculation sets the intended zinc contribution, while the finished batch result can only come from the applicable verification procedure. Where other ingredients also supply zinc, record the zinc sulfate monohydrate contribution separately from the total zinc content of the finished blend.
These checks sit within the formulator’s own quality system. They are not procedures performed or guaranteed by Shivam Agro Industries for a customer’s finished fertilizer.
About Shivam Agro Industries and Its Zinc Sulfate Monohydrate Grades
Shivam Agro Industries, based in Ranasan, Mehsana, Gujarat, offers a product portfolio that spans EDTA salts, amino acid chelates and inorganic mineral products. Its main products include EDTA Disodium, EDTA Zinc, EDTA Ferric, Fe EDDHA and Zinc Bis Glycinate. The inorganic mineral range includes Zinc Sulfate Monohydrate 33% & 36%, alongside copper sulfate and dried magnesium sulfate. The company describes this zinc sulfate monohydrate as highly soluble in water and suited to correcting soil zinc deficiencies in agriculture.
Conclusion: Approving a Zinc Sulfate Monohydrate Grade Switch
The switch to the 36% grade can be approved once the lot assay and its reporting basis are confirmed, the revised formula weight is documented with an approved balancing adjustment, and the applicable batch checks are assigned. At that point the change is a controlled formula revision rather than a substitution made on the production floor.
Before placing a sourcing enquiry, formulation and purchasing teams can confirm current product information and lot documentation for the required grade directly with Shivam Agro Industries.

